Next: About this document ... Up: lab_template Previous: lab_template

Subsections

# Implicit Differentiation

## Purpose

The purpose of this lab is to give you experience using Maple to compute derivatives of functions defined implicitly.

## Background

### Implicit Differentiation

The implicitdiff command can be used to find derivatives of implicitly defined functions. Suppose we wanted to use implicit differentiation to find for the relation

Then we first define our relation and give it a label for later use.
> f:=x^2*y^2+y^3=0;

The syntax of the implicitdiff command is shown by the following example.
> implicitdiff(f,y,x);


The result of the command is the implicit derivative, . The syntax of this command is very similar to that of the diff command. The first argument is always the relation that you want to differentiate implicitly. We were careful to use an equation for this argument, but if you just give an expression for this argument, Maple assumes you want to set this expression equal to zero before differentiating. The second argument to the implicitdiff command is where you tell Maple what the dependent variable is. That is, by putting y here, we were saying that we were thinking of this relation as defining and not . The remaining arguments to implicitdiff are for specifying the order of the derivative you want.

Second derivatives can also be computed with implicitdiff. The following command computes .

> implicitdiff(f,y,x,x);


To compute numerical values of derivatives obtained by implicit differentiation, you have to use the subs command. For example, to find the value of at the point you could use the following command.

> subs({x=1,y=-1},implicitdiff(f,y,x));


Suppose you wanted to find the equation of the tangent line to the graph of at the point . You may want to label the output to at the point as for slope and then you can use the point-slope form of a line to get the equation of the tangent line. The Maple commands below show how this can be done.

> m:=subs({x=1,y=-1},implicitdiff(f,y,x));
> tanline := y-(-1)=m*(x-1);


Sometimes you want the value of a derivative, but first have to find the coordinates of the point. More than likely, you will have to use the fsolve command for this. However, to get the fsolve command to give you the solution you want, you often have to specify a range for the variable. Being able to plot the graph of a relation can be a big help in this task, so we now describe the implicitplot command. This Maple command for plotting implicitly defined functions is in the plots package which must be loaded before using the command.

> with(plots):

Here is an example of using this command to plot the hyperbola . Note that you have to specify both an range and a range. This is because the implicitplot command works by setting up a grid inside the ranges you specify and then using the grid points as starting values in solving the relation numerically.
> implicitplot(x^2-y^2=1,x=-3..3,y=-3..3);

To get a good graph with this command, you usually have to experiment with the ranges. For example the following command
> implicitplot(f,x=-1..1,y=1..2);

produces an empty plot. The reason is simply that there are no solutions to with . This is easy to see if you rewrite the equation as and recognize that both sides of the equation must be nonnegative. Usually a good strategy to follow is to start with fairly large ranges, for example to for both variables, and then refine them based on what you see.

This command can also have problems if the relation in question has solution branches that cross or are too close together. For example, try the following command.

> implicitplot(f,x=-1..1,y=-1..0);

For less than about , you should see the two smooth curves. However, for values of closer to zero the two curves become jagged. To understand this, we need to take a closer look at the relation we tried to plot. The key is to notice that we can factor out and write our relation as follows.

This makes it clear that the graph of the relation really has two pieces: and . These two curves intersect at the origin, which explains why implicitplot has problems there.

As our last example, consider the relation . Try the following commands to see what a part of the graph of this relation looks like.

> g := x^2*sin(y)=1;
> implicitplot(g,x=-4..4,y=-10..10);

Suppose you were asked to find the slope of the graph of this relation at , but you were only given that the value of was about 9. Using the plot, it is relatively easy to find this derivative by first using fsolve to find the value and then substituting into the formula for the derivative. Note the use of a label so we can use the value of in the next command.
> y_sol := fsolve(subs(x=2,g),y=8..10);
> evalf(subs({x=2,y=y_sol},implicitdiff(g,y,x)));


## Exercises

1. Find the slope of the graph of at the point . Label the slope as m.

2. Find the equation of the tangent line to the graph of the relation given above at the point . Be sure to label the tangent line as an implicit relation using the point-slope form of a line. Supply a plot of the relation and the tangent line over the interval and .

3. For the relation from the first exercise, evaluate at the point where and is positive.

4. Consider the circle .
1. Use the implicitplot command to plot the graph of this relation for the region and .
2. Find all points on the graph of the circle where the tangent line is horizontal.

Next: About this document ... Up: lab_template Previous: lab_template
Dina Solitro
2004-09-27